Model NO.
20k 2000w
Power
Ultrasonic
Transport Package
Box
Specification
63*60*30
Trademark
DIZO
Origin
China
Application:
Household Appliances, Garden Supplies, Decoration, Commodity, Auto Part, Electronic
Cooling Way:
Air Cooling
Control:
Automatic
Frequency Range:
Intermediate Frequency
Electric Current:
DC
Style:
Hanging
Prodcct Specifications
Prodcct Specifications
Our Packing
Certifica
FQA
Compared with other welding methods, ultrasonic welding can accept thermoplastic materials. It has many advantages, including process reliability and repeatability, lower energy use than other bonding technologies, saving materials and corresponding labor costs. What are the common problems in ultrasonic welding? What are the specific aspects?
Ultrasonic problem : abnormal overload of ultrasonic current
When the generator sends out an overload alarm, check as follows:
1. Sometimes the no-load test is normal, but it can not work normally. It may be that the internal changes of the welding head and other sound energy components lead to poor sound energy transmission. Here is a relatively simple judgment method: hand touch method. The amplitude of the normal working welding head or horn surface is very uniform, and the hand feels smooth like velvet. When the sound energy transmission is not smooth, there will be bubbles or burr when the sound energy transmission is not smooth. At this time, the elimination method should be used to eliminate the defective parts. When the generator is abnormal, the same situation can be produced, because normally, the input waveform of the transducer should be smooth sine wave. This phenomenon can also occur when there are spikes or abnormal waveforms on the sine wave. In this case, another whole branch acoustic energy element can be used to distinguish.
2. Ultrasonic no-load test, if the working current is normal, it may be that the ultrasonic welding head contacts the object that should not be contacted or the parameter adjustment between the ultrasonic welding head and the welding base is faulty.
3. When the ultrasonic no-load test is abnormal, first observe whether there are cracks in the ultrasonic mold and whether the installation is firm. Then remove the welding head and then conduct the no-load test to exclude whether there is a problem with the ultrasonic transducer + ultrasonic horn, and eliminate step by step. After eliminating the possibility of transducer + horn failure, the new welding head shall be replaced to judge.
| Model | NC-2600DBE |
| Frequency | 15KHZ |
| Power | 6 |
| Welding type | continuouly/intermittet |
| Voltage | 220V 50-60HZ |
| Cooling type | air cooling |
| Current indicates | output amplitude indicates |
| Components | Generator+transducer+ welding head+Franket ring |
| Gross weight | KG20 |
| Working Temp. | -10ºC-40ºC |
| Pressure system | Pneumatical/Manual |
Prodcct Specifications
Our Packing
Certifica
FQA
Compared with other welding methods, ultrasonic welding can accept thermoplastic materials. It has many advantages, including process reliability and repeatability, lower energy use than other bonding technologies, saving materials and corresponding labor costs. What are the common problems in ultrasonic welding? What are the specific aspects?
Ultrasonic problem : abnormal overload of ultrasonic current
When the generator sends out an overload alarm, check as follows:
1. Sometimes the no-load test is normal, but it can not work normally. It may be that the internal changes of the welding head and other sound energy components lead to poor sound energy transmission. Here is a relatively simple judgment method: hand touch method. The amplitude of the normal working welding head or horn surface is very uniform, and the hand feels smooth like velvet. When the sound energy transmission is not smooth, there will be bubbles or burr when the sound energy transmission is not smooth. At this time, the elimination method should be used to eliminate the defective parts. When the generator is abnormal, the same situation can be produced, because normally, the input waveform of the transducer should be smooth sine wave. This phenomenon can also occur when there are spikes or abnormal waveforms on the sine wave. In this case, another whole branch acoustic energy element can be used to distinguish.
2. Ultrasonic no-load test, if the working current is normal, it may be that the ultrasonic welding head contacts the object that should not be contacted or the parameter adjustment between the ultrasonic welding head and the welding base is faulty.
3. When the ultrasonic no-load test is abnormal, first observe whether there are cracks in the ultrasonic mold and whether the installation is firm. Then remove the welding head and then conduct the no-load test to exclude whether there is a problem with the ultrasonic transducer + ultrasonic horn, and eliminate step by step. After eliminating the possibility of transducer + horn failure, the new welding head shall be replaced to judge.
Send Message
