Basic Characteristics Of Motor
•30W (DC Power Supply When Applied To 24VDC/36VDC/48VDC)Rated power (Continuous) | W | 25 (15W/25W) | |||
Rated speed | r/min | 2500 | |||
Rated torque | N.m | 0.096 | |||
Instantaneous maximum torque | N.m | 0.144 | |||
Rotor moment of inertia | J:X10-4kg.m2 | 0.042 | |||
Speed control range | RPM | High pressure 200-2500RPM (Low pressure 200-3000RPM) | |||
Speed control range | On load | Below ±1%: condition 0~rated torque, rated speed, rated voltage, room temperature | |||
On voltage | Below±1%: condition rated voltage ±10%, rated speed, rated load, room temperature | ||||
On temperature | Below±1%: Conditions of ambient temperature 0~+40°C rated voltage, ratod load and rated speed | ||||
Power input | Rated voltage | V | Single phase 110V | Single phase 220V | 24VDC(Optiond 36VDC/48VDC) |
Voltage tolerance range | ±10% | ||||
Frequency | Hz | 50/60 | / | ||
Frequency tolerance range | ±5% | / | |||
Rated input current | A | 1.0 | 0.6 | 1.7 | |
Instantaneous maximum input current | A | 2.0 | 1.2 | 2.6 | |
Product Description
Circular Shaft Type Optical Motor
•Z2BLD30-24GN-30S(2GN5K)-Voltage 24/36/48/110/220
•Z2BLD30-24GN-30S(2GN5K) Diagram (ZD Standard Drive)
•Low Voltage Wrie Plughole Corresp-onding Signal Explanation
plughole | 1 | 2 | 3 | 4 |
signal | U | W | Hv | Hu |
plughole | 5 | 6 | 7 | 8 |
signal | V | GND | Hw | Vcc |
•High Voltage Wrie Plughole Corresp-onding Signal Explanation
| Corresponding meaning | |||||||||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
Blue (coarse) | Yellow (fine) | Yellow (coarse) | Green (fine) | Green (coarse) | Blue (fine) |
| Metal mesh | Red (fine) | Black (fine) |
W | Hu | U | Hv | V | Hw |
|
| Vcc+5V | GND |
•Parallel Shaft Speed Reducer
Z2BLD30-24GN-30S(2GN5K)-Voltage 24/36/48/110/220
1.Connector:5557-8R/10R(MOLEX) 2.The sheath length of lead line 300mm 3.Round terminal:SRA-21T-4(Low ground)
•Decimal Gearhead
2GN()XK ()-Velocity Ratio Value, Generally 10
Gearhead Model | Gear Ratio | L Dimension |
2GN()K | 3-18 | 32&41 |
20~200 | 41 |
•Enter the gear ratio in the box () within the model name
•Z2BLD30-24GN-30S(2GN5K) Machine Allowable Torque (Unit: N.m)
Model | Motor Speed/Reduction Ratio | 3 | 3.6 | 5 | 6 | 7.5 | 9 | 10 | 12.5 | 15 | 18 | 20 | 25 | 30 | 36 | 50 | 60 | 75 | 90 | 100 | 120 | 150 | 180 | 200 |
| Z2BLD30-24GN-30S(2GN5K) | 200~1500RPM | 0.30 | 0.36 | 0.50 | 0.60 | 0.75 | 0.91 | 1.00 | 1.26 | 1.51 | 1.81 | 1.81 | 2.27 | 2.72 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 |
2000RPM | 0.29 | 0.35 | 0.49 | 0.58 | 0.73 | 0.87 | 0.97 | 1.21 | 1.46 | 1.75 | 1.75 | 2.18 | 2.61 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | |
2500RPM | 0.23 | 0.28 | 0.39 | 0.46 | 0.58 | 0.69 | 0.77 | 0.97 | 1.16 | 1.39 | 1.39 | 1.74 | 2.09 | 2.51 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 | 3.00 |
Note :The() (gray) in the table indicates that the rotation direction is consistent with the motor.(The torque under different speed and speed ratio is obtained under the ZD standard.)
•L Type Speed Reducer•Z2BLD30-24GN-30S(2GN5K) Machine Allowable Torque (Unit: N.m)
Motor Speed/Reduction Ratio | 5 | 10 | 15 | 20 | 30 | 50 | 100 | 200 |
200-1500RPM | 0.50 | 1.00 | 1.51 | 2.01 | 2.72 | 4.53 | 9.06 | 16.4 |
2000RPM | 0.43 | 0.85 | 1.28 | 1.70 | 2.30 | 3.83 | 7.67 | 13.9 |
2500RPM | 0.35 | 0.70 | 1.05 | 1.39 | 2.09 | 3.49 | 6.97 | 12.6 |
Note :All gearbox output turn direction in form are opposite as motor turn direction.(The torque under different speed and speed ratio is obtained under the ZD standard.)
Company Information
FAQ
Q: What're your main products?
A: We currently produce Brushed Dc Motors, Brushed Dc Gear Motors, Planetary Dc Gear Motors, Brushless Dc Motors, Stepper motors, Ac Motors and High Precision Planetary Gear Box etc. You can check the specifications for above motors on our website and you can email us to recommend needed motors per your specification too.
Q: How to select a suitable motor?
A:If you have motor pictures or drawings to show us, or you have detailed specs like voltage, speed, torque, motor size, working mode of the motor, needed lifetime and noise level etc, please do not hesitate to let us know, then we can recommend suitable motor per your request accordingly.
Q: Do you have a customized service for your standard motors?
A: Yes, we can customize per your request for the voltage, speed, torque and shaft size/shape. If you need additional wires/cables soldered on the terminal or need to add connectors, or capacitors or EMC we can make it too.
Q: Do you have an individual design service for motors?
A: Yes, we would like to design motors individually for our customers, but it may need some mold developing cost and design charge.
Q: What's your lead time?
A: Generally speaking, our regular standard product will need 15-30days, a bit longer for customized products. But we are very flexible on the lead time, it will depend on the specific orders.
Please contact us if you have detailed requests, thank you !
