The Curtis 803/840 in one instrument a completely solid state battery discharge indicator, an LCD hour meter and lift lockout, housed in a 52mm case. Void of moving parts, this combination instrument is excep
APPLICATION Model 803 is a combination gauge ideally suited for electrically powered vehicles
URTIS INSTRUMENTS PART DESCRIPTION
PRODUCT DESCRIPTION
Curtis Model 803 combines in one instrument a completely solid state battery discharge indicator, an LCD hour meter and lift lockout, housed in a 52mm case. Void of moving parts, this combination instrument is exceptionally reliable even in severe operating environments.
Application: Curtis Model 803 is a combination gauge ideally suited for electrically powered vehicles.
NOTE: In addition to a "U" clamp and thumb nuts/washers shown in the drawing, individually packed units are provided with a mating connector and female pins. Bulk packed units are provided with a "U" clamp and hex nuts/washers only.
Description:
Model: 803RB244BCJ301O
voltage:24/48V
This is alternative item,not orginal part.
Mounting Hardware and Instructions included:
The Model 803 installation Kit includes a pre-assembled mating connector with 5'' terminated wires.
The model 803 fits into a dash-panel cutout measuring 21/16''(52mm)
Overall Dimensions:diameter 51-46mm;thicknees 68mm maximum
• Multicolor 10-bar LED displays state of charge (5 green, 3 yellow, 2 red LEDs).
• Flashing red LED signals "energy reserve" alarm at 70% discharged.
• Double flashing red LEDs signal "empty" alarm at 80% discharged.
• Normally closed relay opens at 80% discharge for lift lockout. This unique holding relay will only lock out at the end of a lift cycle.
• Recognizes improperly charged battery.
• Keyswitch activated LED display (Fuel gauge electronics are energized as long as they remain connected to the battery).
• Wide range adjustable discharge profile.
• Dual reset methods in each gauge: Open Circuit Reset for vehicles that exchange batteries and Charge Tracking Reset for vehicles whose batteries remain connected to the gauge during recharge.
Hour Meter Features
• Monitors use-time throughout the equipment's lifespan.
• Records and displays up to 99,999.9 hours on its LCD, rolls over and continues to count and display.
• Hour meter LCD remains on as long as battery is connected.
• Stores latest total in EEPROM nonvolatile memory, without need of power.
• Operates and displays in temperatures from -40˚C to +65˚C under harsh conditions of vibration, shock, moisture and dust.
System Voltages Available in single voltages from 12 VDC to 80 VDC, or in dual voltage of 24/36, 36/48, 24/48 or 72/80 VDC.
Operating range is ± 25% of nominal voltage
**General product:1234/1236/1238 curtis controller and other controllers are used
Product inforformation :
| Manufacturer | EKOFIL AUTOPARTS COMPANY |
|---|---|
| Part Number | 803RB1224BCG301C |
| Item Weight | 6.2 ounces |
| Country of Origin | China |
| Item model number | 803 |
| Size | Medium |
| Style | Fashion |
| Voltage | 1 Volts |
| Item Package Quantity | 1 |
| Coverage | 11/08/2026 |
| Special Features | 150 |
| Included Components | Cover |
| Batteries Included? | No |
| Batteries Required? | No |
 |
FEATURES
Available with "Spy" or CANopen communication protocols allows use with broad range of controllers. Attractive, easy-to-read, 8 character dot matrix Liquid Crystal Display enhances the look of any vehicle. Two display versions available: Three LEDs: Green to indicate that hour meter is being displayed; Amber to indicate that battery state-of-charge is being displayed; and Red to indicate that a fault has occurred. Six LEDs: 3 Green, 1 Yellow and 1 Red to indicate battery state-of-charge; and 1 Red to indicate that a fault has occurred. Standard models display information from Curtis motor controllers including hours of use, battery state of charge and error/diagnostic messages. Interfaces directly to Curtis motor controllers and displays various system parameters. Molded-in rear Molex style connector provides a low-cost, rugged and reliable installation. Front sealed (IP65) for use in harsh environments
New energy tram in orchard field
E-CAS 100H E-CAS 250H E-CAS S400
Popular sale Controller and Lithium battery
Anhui Ekofil Autopats Company
Our company is located in HEFEI City, ANHUI Province China, is the large-scale professional agriculture Machinery,Forklift Parts manufacturer with integration of manufacturing, export and after-sale service. Establish in 2017, by now Forklift electrical accessories basically cover the vehicles of major domestic brands( Such as Zhongli,Nuoli,Afterburner,Heli,Baoli,TCM TEU)
The company′s main products cover Electric Vehicles,Electric Forklifts,Motor Controller ,Lithium battery and sell parts and accessories for electric Vehicles ,including motors Electric Controls ,meters,accelerators,control handles ,DC converters,power connectors ,wiring harness,Various electrical switches and so on.
We have professional quality inspection department, every machine will be tested 3 times before delivery in order to make sure the machinery in future.
With high quality product, competitive price, and best after-sale service, we have gained good reputation from all over the world, such as Europe, South Korea North, America, Central and South America, Africa, Australia, New Zealand and so on.Base on it ,we welcome buyers from all over the world.
Q1.Can I have a sample order?
A: Yes, we welcome sample order to test and check quality.
Q2. Do you have any MOQ limit?
A: Small quantity is accepted , but we offer quantity discount.
Q3. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping also optional.
Q4. Can you produce according to the samples?
A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.
Q5. Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery.
Q6. Is it OK to print my logo on the product?
A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.
Q7. How to proceed an order?
A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production and Shipping.
