JZ40/1800
Online
1 Year
Electric Winch
Weight Level
3T
Moving
Insulating, Explosion-Proof
CE
National Standards
Jz40/1800
400
1800
1250
2060
1500
60
10
5.2
2.5
Yrt355s-8
90
730
ZHONGMEI
Wooden
4305*4593*3300mm
Shandong China
Product Description
Introduction of Shaft Sinking Winch
Basic InformationUses: It is mainly used for suspending lifting plates, water pumps, water pipes, grouting pipes, air ducts and other digging equipment when digging shafts in coal mines, metal mines and non-metallic mines. It can also be used for other underground and ground lifting and adjusting heavy objects.
Structural characteristics: winding type, including spindle device, reducer, brake and other components.
Characteristics: With large rope capacity and lifting capacity, it is suitable for lifting large equipment and heavy objects.
Operation steps
1. Preparation before starting
Close the power supply: Make sure the air switch is closed and the power supply is connected.
Check the brake: make sure the parking brake has firmly braked the winch and the safety brake is in the braking state.
2. Start the winch
Release the brake: lightly twist the control switch to release the safety brake.
Start the motor: press the start button and the motor starts to run while the working brake is released.
3. Operation control
Lifting or lowering:
Move the main command controller handle from the center position to the lifting or lowering position respectively, the winch starts to lift or lower.
During the operation of the winch, the working condition should be carefully observed to ensure that there are no abnormalities.
Variable speed:
If you need to change the speed, must be carried out in the parking state, and the winch running process is strictly prohibited to change gear.
Use reducer speed change handle to change fast and slow two kinds of speed, back to the rope can be fast and slow two kinds of speed operation, but with the load can only use slow speed.
4. Stopping operation
Preparation before stopping: Gradually lower the load to ensure safety before stopping the machine.
Stop the machine:
Return the main command controller handle to the center position and cut off the power supply of the motor.
Close the pawl and lock to make sure the winch is in safe condition.zmwm21
Parameter of Shaft Sinking Winch
| Model | JZ10/800 | JZ16/800 | JZ16/1000 | 2JZ16/1000 | JZ25/1000 | JZ40/1000 | JZ40/1800 | |
| Wire rope Max. Static tension (KN) | 100 | 160 | 160 | 160 | 250 | 400 | 400 | |
| Wire rope Capacity (m) | 800 | 800 | 1000 | 1320 | 1000 | 1000 | 1800 | |
| Drum specification | Diameter (mm) | 800 | 1000 | 1000 | 1000 | 1050 | 1250 | 1250 |
| Width (mm) | 820 | 1400 | 1400 | 1400 | 1210 | 1480 | 2060 | |
| Center height (mm) | 900 | 1050 | 1050 | 1050 | 1326 | 1500 | 1500 | |
| Wire rope diameter | 32 | 40 | 40 | 40 | 52 | 60 | 60 | |
| Number of winding layers | 8 | 7 | 7 | 8 | 10 | 9 | 10 | |
| First layer rope speed | Fast (m/min) | 5 | 4.7 | 4.7 | 4.7 | 4.8 | 5.2 | 5.2 |
| Slow (m/min) | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | |
| Electric motor | Model | YRT250M2-8 | YRT250M2-8 | YRT250M2-8 | YRT280S-8 | YRT280S-8 | YRT355S-8 | YRT355S-8 |
| Power (KW) | 22 | 30 | 30 | 55 | 45 | 90 | 90 | |
| Speed (RPM) | 730 | 730 | 730 | 723 | 723 | 730 | 730 | |
| Voltage (V) | 380 | 380 | 380 | 380 | 380 | 380 | 380 | |
| Dimensions | Length (mm) | 2883 | 3600 | 3600 | 5726 | 3980 | 4725 | 4305 |
| Width (mm) | 2962 | 3280 | 3280 | 3806 | 3935 | 4593 | 4593 | |
| High (mm) | 1728 | 2300 | 2300 | 2988 | 2620 | 3300 | 3300 | |
| Weight (kg) | 7480 | 11500 | 11500 | 18000 | 14680 | 35000 | 3800 | |
Photos of Shaft Sinking Winch
