BS24245030
24V-310W
12V/6A
12-24/12V
Lead-Acid Battery Charger
Solar Charger
Half-Bridge Charger
24V 50A
Gel, Sealed, Flooded, LiFePO4, Lithium-Ion
Support
Support
99.8%
24V(21-32V)
24V 30A
820W
Oxiang, OEM
Neutral
neutral
Shenzhen
Product Description
DC-DC Inverter & Solar Battery charger
Features
This is a all-automatic DC-DC battery charger, you can use the battery (12V) to charge the battery (12V) (B2B), specially designed for RVs, exposed cars, campers, ships, etc.Technical Data
cable cross section | cable length "+ Start II" | cable length with insulated construction "- Batt." | "Fuse II" cable protection | cable length "- Com." to "- Board I" | cable length "+ Board I" | "Fuse I" cable protection | cable lengths - and + "solar panels" |
| 4mm2 | _ | _ | _ | _ | _ | up to 4m | |
| 6mm2 | _ | _ | _ | _ | _ | up to 6m | |
| 10mm 2 | _ | _ | _ | 0.5-2.0m | 0.5-2.0m | 80A | up to 10m |
| 16mm 2 | up to 7m | up to 7m | 100A | 1.5-3.0m | 1.5-3.0m | 80A | up to 16m |
| 25mm 2 | up to 10m | up to 10m | 100A | 2.5-5.0m | 2.5-5.0m | 80A | _ |
cable cross section | cable length "+ Start II" | cable length with insulated construction "- Batt." | "Fuse II" cable protection | cable length "- Com." to "- Board I" | cable length "+ Board I" | "Fuse I" cable protection | cable lengths - and + "solar panels" |
| 4mm2 | _ | _ | _ | _ | _ | up to 4m | |
| 6mm2 | _ | _ | _ | _ | _ | up to 6m | |
| 10mm 2 | _ | _ | _ | 0.5-2.0m | 0.5-2.0m | 80A | up to 10m |
| 16mm 2 | up to 7m | up to 7m | 100A | 1.5-3.0m | 1.5-3.0m | 80A | up to 16m |
| 25mm 2 | up to 10m | up to 10m | 100A | 2.5-5.0m | 2.5-5.0m | 80A | _ |
B2B Operation
mobile operation from dynamo and starter battery (Battery to Battery):
it refers to charging the main battery through dynamo and starter battery, .If it is not used in the Vehicle , you can also use one battery (12V) to charge another
- . The efficient charging converter (booster) allows full charging of the board battery during driving.
- . It increases/reduces the voltage to the level, which is required for precise charging of the board battery with the optimum characteristic line of charging.
- . The simultaneously supplied 12 V consumers are protected against overvoltage and voltage fluctuations.
Further Characteristics of the Unit
- The output voltage is stabilized, free of peaks, smoothed and filtered.
- Galvanic isolation between input and output:
- No overvoltage at the output and thus protection of the consumer if the ground line is lost.
- Clean, undisturbed mass ratios, even with long supply lines.
- Stable operating voltage on site in mobile operation, e.g. Containers, trailers, roll containers etc.
- Filtering and suppression of disturbances on the input to the output side.
- Fully automatic continuous operation: The DC-DC converter can constantly work with the battery
- Surveillance-free operation: multiple protection against overload, overheating, over voltage, short circuit, Misconduct and deep discharge of the battery through electronic regulation to complete
- Switch off by built-in safety switch.
Function
Security guidelines
Intended use:
The DC-DC converter was built on the basis of the valid safety guidelines. The use may only be:
- On lead-acid, lead-gel or lead AGM or LiFePO4 batteries of the specified nominal voltage.
- With the specified cable cross-sections for inputs and outputs.
- With fuses of the specified strength near the battery to protect the wiring between the batteries and DC-DC converter connections.
The device must never be used in places where there is a risk of gas or dust explosion consists!
Installation of the Unit
- . Install the charger near the board supply battery I (for short charging cables) at a clean, even and hard mounting surface,which is protected from moisture, humidity and aggressive battery gases. The unit can be installed in any position.
- . To be installed in a moisture-proof, water-proof place, corrosion-proof place
- . When the charging controller is working, the fan will bring out heat, so when installing, ensure that there is at least 10cm of space behind the charger controller
- . Choose the appropriate cable specifications, length and fuse specifications, reverse connection of the battery will cause serious damage to the equipment
Why Choose us?
> Oxiang is located in Shenzhen, China, a new type of city in rapid development. We focus on CCTV Camera researching and manufacturing from 2006;
> Sales person provide Pre-sales and after-sales service; Professional engineers are always standby and assist offer solutions;
> Cooperate with multiple departments to complete raw material procurement, production, inspection, delivery and other steps;
> The product comes with a one-year warranty.
