Power Input

Voltage and power range

3 phaseU4N: 380~500VAC [-10%...+10%]
3 phase U6N: 520~690VAC [-10%...+10%]

Input frequency

45~65Hz

Control Feature

Control mode

Vector control

THDi(under rated current)

<4%(Harmonic meet IEEEE519 requirements )

Power factor

Over 0.95(under rated current)

Overload ability

150% 1min

Carrier frequency

2~4k(Hz)

Efficiency(under rated current)

>97%

Power Input

Input Voltage

U4N:DC  power:450~800Vdc
U6N:DC  power:740~1200Vdc

Power Output

Output Voltage

0VAC~Un

Output frequency

V/F control:0.00~300.00Hz
Vector control:0.00~120.00Hz

Overload ability

Run at 40ºC,heavy load 150%,1min, light load 120%,1min

Efficiency (Full load)

≥0.97

Control Feature

Control mode

V/F control

Open loop vector control

Close loop

Starting Torque

2.50Hz  150%

0.5Hz  200%

0.00Hz  200%

Speed range

1:50

1:200

1:1000

Steady speed precision

± 2%

± 0.2%

± 0.02%

Torque precision

±5%(Close loop control)

4/5000 Carrier frequency

2~4kHz;The carrier frequency can be automatically adjusted according to the load characteristics

frequency set Resolution

0.01Hz(Digital command)
±0.06Hz/120Hz(Analog command 11bit +unsigned)

Running command channel

Operation panel given, control terminal given, communication given

Frequency given channel

Operation panel given, digital/analog given, communication given, function given

Torque increase

Automatic torque lift, manual torque lift

V/F Curve

User - defined V/F curve, linear V/F curve and 3 kinds of reduced torque characteristic curves

Automatic voltage regulation

The duty cycle of output PWM signal is automatically adjusted according to the bus voltage fluctuation, so as to reduce the influence of the network voltage fluctuation on the output voltage fluctuation

Instantaneous power loss processing

Instantaneous power loss, through bus voltage control, uninterrupted operation

Dc braking capacity

Braking current:0.0~120.0% rated current

 
     Features

 Parameters copy

Standard operation panel can achieve parameters upload, download, there is a copy of progress instructions

Process PID

Can be used for closed-loop control of process quantities

Torque control function

Torque/speed control can be switched through the terminal, a variety of torque given way

Zero servo and position control function

Zero speed position locking, precise positioning and position control can be achieved

Motor Protection

Rotor blocked

Motor overload

Speed limit

Torque limit

Output current limit

Inverter onverload

IGBT I 2t protection

Input power undervoltage/overvoltage

Dc bus undervoltage/overvoltage

IGBT overheat

Cooling fan overheat

Power failure

Loss of analog input signal (loss of speed reference value)

Abnormal communication

Encoder connection failure

Self tuning fault

 
    Environmental conditions

Use place

Installed vertically in a well ventilated electric control cabinet; Horizontal or other installation method flat or other installation method is not allowed.
Installed in the direct sunlight, no dust, no corrosive gas, no flammable gas, no oil mist, no steam, no dripping environment. The cooling medium is air.

Operating environment requirement

-10ºC(No freezing)-+40ºC

Temperature drop using

>40ºC,Every increase 1ºC,rated output current reduce 2%, max 50ºC

Storage temperature

-40ºC-+70ºC

Transportation temperature

-40ºC-+70ºC

Relative humidity

5~95%RH,No condensation, no corrosion, no dripping

Storage

IEC60721-3-1
Class 1C2(Chemical gas)Class 1S2(Solid particles)

Transportation

IEC60721-3-2
Class 2C2(Chemical gas)Class 2S2(Solid particles)

Operation

IEC60721-3-3
Class 3C1/3C2*(Chemical gas)Class 3S2(Solid particles)
C=Chemically active substance,S=Mechanically active material,*Coated circuit board

The altitude

1000m

Height drop using

>1000m,Every increase 100m,rated output current reduce 1%(max 3000m)

Anti-shock performance

3.5m/s2,2~9Hz;10m/s2,9~120Hz;

Protection grade

IP20

Others

Cooling way

Forced air cooling

Installation way

Inside cabinet installation

Protective coating

Control panel, I/O panel, and other optional reinforced protective coating

Product standards

C E
LV terms 73/23/EEC subject to amendment 93/68/EEC
Mechanical terms 98/37/EC
EMC terms 89/336/EEC subject to amendment93/68/EEC
Quality assurance system ISO 9001 and
Environment system ISO 14001