Model NO.
M711 & 629 wireless
Voltage
DC 12V
Video Output
2 RCA
Video Inputs
2
Audio Output
Digital Optical Output
TV System
PAL/NTSC
Camera Type
IR Night Vision
Transport Package
Neutral Retail Box, Then Into Carton
Trademark
CE
Origin
Shenzhen, China
HS Code
852891090
Production Capacity
12000 Sets/Month
Applicable Model:
Engineering Vehicles, Sightseeing Car, Truck, RV, Van
Screen Size:
7"
Waterproof Grade:
IP68
Certification:
CE
Warranty:
12 Months
Material:
Plastic
Color CMOS Camera:
- Pick-up Device: 1/4" CMOS
- TV System: PAL (CCIR), NTSC (EIA)
- Scanning System: PAL: 625 Lines; NTSC: 525 Lines, 60 Field
- Lens: 2.8 mm (Option)
- Number of Pixels: 500 (H) * 582 (V), 510 (H) * 492 (V)
- Horizontal Resolution: 420 TV Lines
- Scan Frequency: 50 Hz, 60Hz
- Electronic Shutter: 1/50 - 1/100 (sec) 1/60 - 1/100,100 (sec)
- S/N Ratio: >=48dB (AGC OFF)
- Minimun Illumination: 0.8 Lux / F1.2
- BLC: Open
- White Balance: Auto
- Gain Control (AGC): Auto
- Video Output: 1.0 Vp - p.75 Ω, BNC Connector
- Synchronous System: Internal Synchronization
- Operation Temperature: -20 Celsius - +80 Celsius
- Power Supply: DC 12V - 24V
- Focal Distance: 30mm to Infinite
7'' CAR TFT LCD Monitor:
- Display Size: 7 Inch
- Resolution: 480 (W) * RGB * 234 (H)
- System: PAL & NTSC
- Power Supply: DC 9V - 35V
- Consumption: 6W
- Video: 2 - Channel Video Input, V1 / V2 Switch
- Audio: One Way Volume Input
- Net Weight: Around 740g
2.4G Wireless Color Video Transmitter and Receiver
- Receiver/transmitter frequency: 2400 ~ 2483MHz Transmission Power 10mW / CE 2mW / FCC frequency range 2400 ~ 2483.5MHz
- Operating frequency: 2414MHz / 2432MHz / 2450MHz / 2468MHz (optional)
- Power output: 100MW;
- Voltage: DC= 9V / 12V;
- Video IN/OUT: PAL/NTSC composite video signal
- Car closed condition Signal range: 34ft (open areas)
- AV OUT interface: RCA jack
- Operating temperature: -10 degrees to +50 degrees
- Storage temperature: -30 degrees to +50 degrees
- install: The camera is connected with the transmitter, the transmitter from the reversing light (mounted on the back) or brakes (mounted in front) connected to 12V power supply. Receiver directly plugged into the cigarette lighter or 12V power connection
Installation instructions:
- The unit that is labeled "2.4 G wireless color video receivers" is the signal receiver. The other unit that is labeled "2.4 G wireless color video" is the signal transmitter.
- Firstly, you should connect the camera with the transmitter. The yellow interface is for video and the red one is for power. Then connect the wire of the transmitter to the backup light of your vehicle. After theses, mount the camera on your vehicle with two screw s. There are two holes on the case of the camera.
- Secondly, connect the extension power cord to the monitor. The red wire and the black wire of the cable is used to connect the 12V/24V power source of the vehicle. The blue one is connected to the back up light. Then connect V1 cable (for video) with the receiver. The wire of the receiver connects to the reverse circuit in the auto fuse box.
Send Message
