Model NO.
IT-W701A
Paint Mist Treatment
Dry-type
Condition
New
Product Name
Infitech Customized Car Spray Booth Oven with Wate
Keyword
Spray Booth Oven
Voltage
415V, 50Hz, Your Special Voltage Is Acceptable
Illumination
> 1000lux
Intake/Exhaust System
7.5kw, 970rpm, 415V, 50Hz, Explosion-Proof Motor
Equipment Empty Loaded Air Speed
+/- 0.28m/S
Noise
<78dB
Burner Model
Riello Diesel Burner Rg5d
Rated Power
18kw
Warranty
2years
Transport Package
Polyfoam and Metal Frame
Specification
7000 X 4000 X 2800mm
Trademark
INFITECH
Origin
China
HS Code
8419899090
Production Capacity
500 Sets / Year
Type:
Spray Booth
Certification:
CE
Substrate:
Steel
Coating:
Powder Coating
Airflow Direction:
Fully Undershot-type
Heating Mode:
Diesel
INFITECH Meet Australian Standard Car Paint Chamber With Water-Based System
Production Design
Pruduct description
Technical parameters
| Design standar | AS/NZS 4114.1:2003 |
| Internal dimensions | 7000 X 4000 X 2800mm (L X W X H) |
| External dimensions | 7110 X 5870 X 3810mm (L X W X H) |
| Drive-in-ramps | 3 pieces; size: 2000 X 1030 X 320mm, diamond structure |
| Plenum height | 600mm |
| Wall panel | 50mm dual-skin insulated panels filled with heat resistant rock wool |
| Top panel | 50mm dual-skin insulated panels filled with heat resistant rock wool |
| Entrcan door | Manual door, 3 wing entry door (2 + 1 structure) |
| Size | 3200 X 2700mm (W X H) |
| Personnel door | 2 sets 800 X 2000 mm (W X H) |
| Door description | With safety glass observation window |
| Sidewall lighting | LED lamp accessible from outside the booth |
| Quantity and power | 6 sets of light fixtures, each 2 X 18W, 216W total |
| Ceiling lighting | LED lamp accessible from outside the booth |
| Quantity and power | 8 sets of light fixtures, each 4 X 18W, 576W total |
| Brightness | > 1000Lux |
| Filtration system | Pre-filter, Ceiling filter, Floor filter, Exhaust filter |
| Intake/Exhaust system | Direct-type turbine fan,7.5KW, 970rpm, 415V, 50Hz, explosion-proof motor, SIEMENS |
| Parameter of fan | 28,000m3/h, 650pa |
| Empty loaded air speed | +/- 0.28m/s |
| Noise | <78db |
| Heating system | Stainless steel 0Cr25Ni20 (SUS310) |
| Heat exchanger power | 232KW |
| Temperature increase capability | 25° C (from -5°C to 20°C in painting phase) |
| Max. working temperature | 80°C |
| Heating time | 5-8 minutes (from 20°C to 60°C in baking phase) |
| Burner model | RIELLO diesel burner RG5D |
| Control system | Standard Y/Δ step-down start control system |
| PLC programmable logic controller | PLC control, higher reliability, lower failure rate |
| Pressure detection | Pressure gauge indicates pressure inside the booth. |
| Features | Painting, heating painting, flash-off, baking, lighting, emergency stop switch, failure indication, baking delay stop protection, motor overload and over-current protection, with stack light |
| Safety device | Front door pressure sensor, safety door pressure sensor, exhaust air fan limit switch, filter blockage detection switch, fan and heating system interlock control, over-temperature alarm indication |
| Rate power | 18KW |
| Special item | Water-based paint drying system Features: - The blowers (of the water-based system) take clean air from the top plenum directly, ensuring that the air volume of the booth is kept at 28,000m3/h and maintaining the balance of the inlet airflow and outlet airflow. - It expedites the air velocity of the internal cycle in the flash and baking phase. The air velocity around the vehicle is greatly accelerated, and the effect of fast drying is achieved. - It helps greatly improve the painting efficiency, and achieve the aim of cost-effectiveness and production efficiency improvement. |
Entrance door
3200 X 2700mm (W X H)
Manual door, 3 wing entry door (2 + 1 structure)
Containing frame, with safety glass observation window
Safety device
Cabin structure
- "Π" beam made from 80 x 80 square tubes.
- "Π" beams: linked and reinforced by 80 x 80 or 80 x 40 square tubes, evenly distributed along the cabin.
- "Π" beam made from 80 x 80 square tubes.
- "Π" beams: linked and reinforced by 80 x 80 or 80 x 40 square tubes, evenly distributed along the cabin.
Lighting system
- Accessible from outside the boot
Basement
- Assembly structure, with adjustable support foot which fits less than 30mm height ground unevenness- Plug-in type grid structure, full grids.
- Fiber-glass paint-stop filter (laid under the grids)
Intake&Exhaust system
- Accessible from outside the boot
- Money saving energy efficient T-8 fixtures
- Sealed fixtures fitted with tempered glass
- IP55 protection grade, light fixtures fully meet EU standards
- 23 degree angled ceiling lights + vertical sidewall lightsBasement
- Assembly structure, with adjustable support foot which fits less than 30mm height ground unevenness
- Fiber-glass paint-stop filter (laid under the grids)
Intake&Exhaust system
Water-based paint drying system
- Reduce the leveling time
Control system
- Main optional components: SIEMENS, OMRON, etc.
- Control board conforms to EN602041-2006.
- Control order conforms to EN133552004.
- Control box conforms to IP55 protection grade.
Engineering case
Company introduction
Guangzhou Infitech is professional manufacturer of customized European standard spray booths in China. We stick to European standard for spray booth since the business started. What we supply ranges from initial design and layout, technical consultation, manufacturing through to installation and maintenance. We pride ourselves in delivering customized products that suit your customers' individual needs.
- Reduce the leveling time
- Reduce the curing time.
- Accelerate solvent volatilization (before the start of baking cycle)
- Accelerate solvent volatilization (before the start of baking cycle)
Control system
- Main optional components: SIEMENS, OMRON, etc.
- Control board conforms to EN602041-2006.
- Control order conforms to EN133552004.
- Control box conforms to IP55 protection grade.
Engineering case
Company introduction
Guangzhou Infitech is professional manufacturer of customized European standard spray booths in China. We stick to European standard for spray booth since the business started. What we supply ranges from initial design and layout, technical consultation, manufacturing through to installation and maintenance. We pride ourselves in delivering customized products that suit your customers' individual needs.
Send Message
